JL Audio XD200/2: 2 Ch. Class D Full-Range Amplifier 200 W

(1 review) Write a Review
4.00 LBS
Calculated at Checkout
  • JL Audio XD200/2: 2 Ch. Class D Full-Range Amplifier 200 W
  • JL Audio XD200/2: 2 Ch. Class D Full-Range Amplifier 200 W


JL Audio XD200/2

This tiny amplifier packs a serious full-range punch, delivering a staggering 100 watts per channel into 2 ohms (14.4V, 1% THD). The breakthrough that makes this much power possible in such a small chassis is our NexD™ ultra-high-speed switching design, which allows for full bandwidth Class D operation with extremely low distortion and outstanding efficiency.

The XD200/2v2 includes a 12 dB / octave filter which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz.

The XD200/2v2 also features the v2 Spec feature set, which consists of automatic turn-on capability (via signal sensing or DC-offset sensing), and a dual-range differential-balanced input section able to handle a wide range of input voltage levels. With the addition of an HD-RLC remote level control (sold separately), the amplifier's level can be directly controlled from the driver's seat.

Rated Continuous (RMS) Power @ 14.4 V

@ 4 Ω 75 W RMS x 2
@ 2 Ω 100 W RMS x 2
Bridged @ 4Ω 200 W RMS x 1

Rated Continuous (RMS) Power @ 12.5 V

@ 4 Ω 60 W RMS x 2
@ 2 Ω 90 W RMS x 2
Bridged @ 4Ω 180 W RMS x 1

General Specifications

Frequency Response 12 Hz - 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Damping Factor @ 4 Ω >150 / 50 Hz
Damping Factor @ 2 Ω >75 / 50 Hz
THD+N @ Rated Power <1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge 8 AWG wire
Fuse Rating 20 A (AFS, AGU or MaxiFuse™)

Signal Processing

Filter Mode(s) Low-Pass or High-Pass
Filter Slope(s) 12 dB/octave
Filter Frequency Range 50 Hz - 500 Hz
Detented, Calibrated Filter Freq. Potentiometer Yes
Filter Defeat Function Yes
Remote Level Control Optional (HD-RLC)
Security Cover for Controls Yes
Pass-Through Preamp Output Buffered

Physical Specifications

Height (H) 2.05 in / 52 mm
Width (W) 6.85 in / 174 mm
Depth (D) 7.09 in / 180 mm
Net Weight 3.75 lb / 1.70 kg
View AllClose

Additional Information

Manufacture SKU #:
Number Of Channels:
2 Channel
RMS Power In Watts:
1-250 Watts
View AllClose

1 Review

  • 5
    More than 200 amps of clean output

    Posted by S Lawrence Ram on 7th Feb 2019

    Ok this amp from JL Audio is ridiculous and I mean in a good way. I am sure that this amp can push way more than 200 watts RMS. They say you can bridge this amp at 4 Ohms for 200 watts. Well let me tell you what JL Audio didn’t tell you not to do. I currently have a 10W7 hooked up to this amp bridged. Now if you know the 10w7, it has an impedance if 3 ohms. I am bridging 3 ohms in an amp that says bridge at 4 ohms according to the manual. Amazing. I know that this sub is underpowered right now, but my goodness it sounds good! My amp didn’t even get hot. I was so worried about bridging 3 ohms and it surprised the heck out of me. Thank JL Audio and thank you Creative Audio!

View AllClose