Clarion M608 Marine Receiver with CMS-651RGB-SWB 6.5-inch LED RGB Marine Coaxial Speakers, Sport Grilles Includes Lighting Remote

Included in this kit

---

This bundle includes a Clarion M608 Marine Bluetooth Watertight 4-Zone Digital Media Reciever, a Clarion CMS-651RGB-SWB 6.5-inch Coaxial Marine Speakers with built-in RGB illumination 30W RMS power handling 1/2-inch (13 mm) polymer dome tweeter Includes White & Black Sport Grilles, and a Clarion CMR-L1 Marine LED Light Controller.

1x Clarion M608 Marine Bluetooth Watertight 4-Zone Digital Media Reciever - (M608)

Water and salt can be a marine source unit's worst nightmare. Our M608 source unit is IP55 tested and certified to provide you the best in water intrusion and salt water protection in its class, at the front panel where it’s most exposed to the elements. Internally, rubber gaskets stop water in its tracks and integrated drainage channels keep water out, with an IPX3 tested and certified stainless steel chassis for protection even if water manages to seep into the console. Its single DIN chassis and face make it an excellent replacement system for smaller or older boats, while its upscale design fits right in with today’s highly stylized boat consoles and cabins. The two-line LCD display is able to show the information you need. The 13-digit 2-line display on the M608 allows characters to be displayed clearly in all lighting conditions.

Frequency bands FM/AM/Weather Band
FM Tuner
Frequency Range 87.9 ～ 107.9 MHz (0.2 MHz STEP)
AM Tuner
Frequency Range 530 ～ 1710 kHz (10 kHz STEP)
Weather Band
NOAA Frequency Range 162.400MHz ～162.550MHz
Channel 1 : 162.400MHz
Channel 2 : 162.425MHz
Channel 3 : 162.450MHz
Channel 4 : 162.475MHz
Channel 5 : 162.500MHz
Channel 6 : 162.525MHz
Channel 7 : 162.550MHz
Bluetooth
Profile A2DP (Advanced Audio Distribution Profile)
AptX
AVRCP (AV Remote Control Profile)
SPP (Serial Port Profile)
SSP (Simple Secure Pairing)
Bluetooth Auto Connect ●
AUDIO
Maximum Power Output 50 W × 4
High Pass Filter / Low Pass Filter ● 60/90/120/Through
GENERAL
Dimensions (W × H × D) (Inches) Chassis Area (No Escutcheon): 6 31/32 x 7 43/64 x 1 31/32
Escutcheon: 7 41/64 x 15/16 x 3 25/64
Dimensions (W × H × D) (mm) Chassis Area (No Escutcheon): 177 x 195 x 50
Escutcheon: 194 x 24 x 86
Low Consumption Mode as Power Off <50mA when POWER=OFF (Need < 3mA when ACC=OFF)

1x Clarion CMS-651RGB-SWB 6.5-inch Coaxial Marine Speakers with built-in RGB illumination 30W RMS power handling 1/2-inch (13 mm) polymer dome tweeter Includes White & Black Sport Grilles - (CMS-651RGB-SWB)

Includes White & Black Sport Grilles
Salt & Sun Certified
Built-In RGB LED Lighting
30W RMS power handling, perfect for source unit-powered systems
Bridge-mounted, 1/2-inch (13 mm) balanced-dome, polymer tweeter with neodymium magnet and ferrofluid cooling
Standard cutout size and mounting hole for easy retrofitting

1x Clarion CMR-L1 Marine LED Light Controller - (CMR-L1)

The Clarion CMR-L1 Marine LED light controller adds some flair to Clarion and other RGB LED marine speakers!

Specifications:
• Dynamic Modes 20
• Dynamic Speed Levels 10
• Static Colors 20
• Direct Preset Colors 7
• Brightness Levels 8
• Operating Voltage 10- 15V DC
• Operating Temp Range -4 ° F to + 1 58 ° F, (-20 °C to + 70 °C)
• Operating Frequency 433.92 MHz
• Operating Range* Up to 15 m (49.2 ft)
• Output Capacity 2 A (maximum)
• Recommended Fuse Value 10 A (maximum)
• Transmitter Battery CR2025 (3V)
• Dimensions 2. 99 in x 2 in x 1 .07 in
• (Transmitter) 76 mm x 50.8 mm x 27.2 mm
• Dimensions 4.02 in x 3.01 in x 1.42 in
• (Receiver) 102.1 mm x 76.5 mm x 36.1 mm

Notes:
• Install in a dry, well-ventilated location; do not install in an engine compartment or other areas of extreme heat. Do not install where it will be directly exposed to the elements.
• To optimize performance, avoid confined installation locations or areas surrounded by metal; maintain at least 25 cm (10 in) of separation from any audio signal cables.
• Make sure the total amperage demands of all connected LED circuits does not exceed the output capacity of the controller.
• *Install a fuse (not included) at the main +12V power wire (Red) connection point that is appropriate for the total current draw of all LED circuits (up to 10 A).
• For short-circuit protection, we recommend installing a fuse (not included) at EACH speaker's +12V LED connection lead. Refer to your speaker's LED specifications for individual fuse values.