Description
Included in this kit
This bundle includes a JL Audio JD400/4 4-channel Class D full-range amplifier, and 2x JL Audio C1-650se 6.5" C1 2-Way Component System, Silk Edition.
1x JL Audio JD400/4 4-channel Class D full-range amplifier - (JD400/4)
JL Audio JD400/4
Compact and Versatile: Fits nearly anywhere: 9.50 x 7.50 x 2.10 in. (242 x 190 x 53 mm) Ultra-flexible outputs, capable of multiple configurations:4-Ch. Satellite Amp: power front and rear speakers with 75W x 43-Ch. System Amp: power front speakers with 75W x 2 and a sub with up to 200W2-Ch. High-Power Satellite Amp: power 2pr. of speakers with 200W x 22-Ch. High-Power Subwoofer Amp: drive two subwoofers with 200W x 2
NexD™ Switching Amplifier Technology: Our advanced high-speed switching technology delivers outstanding fidelity with very low noise and distortion. Exceptional efficiency results in reduced current draw and heat, permitting reliable high power output within a very small chassis. Full-bandwidth operation in all channels. (20 Hz - 20 kHz bandwidth)
Complete Signal Processing Sections: 12dB/octave high or low-pass filters for each channel pair, defeatable, with fully variable frequency selection from 50-500 Hz. Preamp outputs (buffered, pass-through type, from CH. 1&2)
Dual-Range, Differential-Balanced Inputs and Automatic Turn-On Capabilities: NO NOISE! Outstanding noise rejection prevents alternator whine and other noises. Accepts line-level or speaker level signals up to 8V RMS, including those from factory systems, without a line-output converter (LOC): just splice wires to a pair of RCA ends or RCA cables. Selectable Input Mode switch permits one pair of inputs to feed both pairs of output channels. Automatic turn-on option via Signal-Sensing or DC-Offset sensing
Integrated LED Clipping Indicators for Easy Setup: Simplifies input-sensitivity setting by providing accurate visual feedback of output clipping level.1) Disconnect one speaker output wire2) Play full-scale (0 dBfs) sine-wave through audio system, with head unit at 3/4 volume and tone controls set flat.3) Adjust input sensitivity until light turns on, then back off slightly. Separate, top-mounted LEDs report overall status and condition
Rated Continuous (RMS) Power @ 14.4 V
| @ 4 Ω | 75 W RMS x 4 |
| @ 2 Ω | 100 W RMS x 4 |
| Bridged @ 4Ω | 200 W RMS x 2 |
General Specifications
| Frequency Response | 20 Hz - 20 kHz (+0, -1dB) |
| S/N Ratio, referred to highest rated power | >93 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| S/N Ratio, referred to 1 W | >76 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| Damping Factor @ 4 Ω | >60 / 50 Hz |
| Damping Factor @ 2 Ω | >30 / 50 Hz |
| THD+N @ Rated Power | <1% @ 2 Ω per Ch. |
| Input Voltage Range @ RCA Inputs | 200 mV - 4 V RMS |
| Input Voltage Range @ High-Level Inputs | 2 V - 10 V RMS |
| Min.Copper Power / Ground Wire Gauge | 4 AWG wire |
| Fuse Rating | 40 A (AFS, AGU or MaxiFuse™) |
Signal Processing
| Filter Mode(s) | Low-Pass or High-Pass |
| Filter Slope(s) | 12 dB/octave |
| Filter Frequency Range | 50 Hz - 200 Hz |
| Detented, Calibrated Filter Freq. Potentiometers | No |
| Filter Defeat Function | Yes |
| Remote Level Control | No |
| Remote Level Modes | N/A |
| Channel Input Mode Switch | Yes (2/4 ch.) |
| Pass-Through Preamp Output | Unbuffered |
| Source Channel Selection for PreOuts | No (always 2 Ch) |
Physical Specifications
| Height (H) | 2.10 in / 53 mm |
| Width (W) | 9.50 in / 242 mm |
| Depth (D) | 7.5 in / 190 mm |
2x JL Audio C1-650se 6.5" C1 2-Way Component System, Silk Edition - (C1-650se)
2-Way Component System: 6.5-inch (165 mm) Woofer, 1-inch (25 mm) Silk Dome Tweeter
The C1-650se component system is engineered to deliver remarkable fidelity and outstanding value in a format that easily fits in factory locations.Outfitted with pure, silk dome tweeters, the C1-650se component system stands above others in its category with silky smooth, high-frequency clarity and definition. The 1-inch tweeter’s edge-driven design delivers excellent off-axis response and treble extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. Outboard, 3rd order, high-pass in-line filters, with Advanced Tweeter Protection Circuitry, are also included to guard against high-distortion damage and improve power handling. For maximum installation versatility, surface and flush tweeter mounts are also included.
C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low-distortion sound. At the core of the C1-650 woofer is a proprietary, stamped, steel 6.5-inch (165 mm) frame and DMA-optimized motor system. A mineral-filled, injection-molded, polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to each spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
To maximize fit, multi-application adaptor rings are included for the woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well.
When it comes to value, C1-650se is a real deal!
Sold as a pair. Grilles not available.
General Specifications
Continuous Power Handling (RMS): 50 WRecommended Amplifier Power (RMS): 10 - 75 W / Ch.
System Efficiency: 91.0 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 48 Hz - 21 KHz ± 3 dB
Woofer Physical Specifications
Frame Outer Diameter* (A): 6.25 in / 159 mmGrille Tray Outer Diameter (B): 6.84 in / 174 mm
Motor Outer Diameter (C): 3.15 in / 80 mm
Frontal Coaxial Tweeter Protrusion (D): N/A
Frontal Grille Protrusion** (E): N/A
Mounting Hole Diameter (F): 5.02 in / 128 mm
Mounting Depth (G): 2.07 in / 53 mm
*Does not take into account mounting tabs **Frontal grille protrusion measured from m
ounting surface
Tweeter Physical Specifications
Flush Mount Fixture Diameter (A1): 1.97 in / 50 mmSurface Mount Fixture Diameter (A2): 2.01 in / 51 mm
Flush Mount Mounting Hole Diameter (B): 1.75 in / 45 mm
Flush Mount Mounting Depth (C): 0.40 in / 10 mm
Flush Mount Tweeter Frontal Protrusion (D1): 0.32 in / 8 mm
Surface Mount Tweeter Frontal Protrusion (D2): 0.87 in / 22 mm