Description
Included in this kit
This bundle includes a Stinger RKFR69 Roadkill Fast Rings 6x9", and a JL Audio C1-690x 6 x 9-inch (150 x 230mm) Coaxial Speakers with 0.75-inch (19mm) aluminum dome tweeters.
1x Stinger RKFR69 Roadkill Fast Rings 6x9" - (RKFR69)
Our 3-piece foam ring speaker enhancement system solves the problem of acoustically coupling aftermarket speakers to factory speaker openings. The RoadKill Fast Rings kit increases speaker output, improves the projection of the audio into the car cabin and reduces unwanted rear reflections that can degrade the sound.
3-piece Foam Ring System fits 6x9" Speakers
Features:
• Reduce panel vibration
• Increase mid-bass response
• Enhanced audio output efficiency
• Minimize destructive wave interference
• Help prevent front and rear wave cancellation
• Easy installation with peel & stick application
• Maximize performance for speaker installations
• Sold in pairs
3 Ring DNA
• Gasket for speaker mounting to the baffle plate surface
• Middle ring to mount around the outer edge of the speaker
• Circular foam pad goes behind the speaker to absorb unwanted reflections on hard surfaces, such as inside a car door
1x JL Audio C1-690x 6 x 9-inch (150 x 230mm) Coaxial Speakers with 0.75-inch (19mm) aluminum dome tweeters - (C1-690x)
JL Audio C1-690x
Coaxial Speaker System: 6 x 9-inch (150 x 230 mm) Woofer, 1.0-inch (25 mm) Aluminum Dome Tweeter
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690x to be installed in bottom-mount applications.
C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690x is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling.
Sold as a pair. Grilles not included.
General Specifications
| Continuous Power Handling (RMS) | 60 W |
| Peak Music Power | 225 W |
| Recommended Amplifier Power (RMS) | 10 - 100 W / Ch. |
| System Efficiency | 91.5 dB @ 1 W / 1 m |
| System Nominal Impedance | 4 Ω |
| System Frequency Response | 39 Hz - 22 KHz ± 3 dB |
Physical Specifications
| Frame Outer Diameter* (A) | 6.38 x 9.33 in / 162 x 237 mm |
| Grille Tray Outer Diameter (B) | N/A |
| Motor Outer Diameter (C) | 3.54 in / 90 mm |
| Frontal Coaxial Tweeter Protrusion** (D) | 0.41 in / 10 mm |
| Frontal Grille Protrusion (E) | N/A |
| Mounting Hole Diameter (F) | N/A |
| Mounting Depth (G) | 2.75 in / 70 mm |