Included in this kit This bundle includes a JL Audio RD800/6 6-channel full-range amplifier 800 watts, 2x JL Audio C7-650cw 6.50-inch (165mm) Component Woofer Grille included, 2x JL Audio C7-350cm 3.5-inch (90mm) Component Midrange Driver Grille included, and 2x JL Audio C7-100ct 1-inch (19mm) Corundum ceramic-coated, aluminum dome tweeter Grille included.
1x JL Audio RD800/6 6-channel full-range amplifier 800 watts - (RD800/6) SLEEK, POWERFUL, PACKED WITH VALUE
The look is amazing, and the performance backs it up. These ultracompact full-range RD series amplifiers from JL Audio are engineered to generate loads of power with exceptional efficiency and low distortion. The result: premium audio quality with significantly reduced current draw and heat.
General
Channels: 6
Physical dimensions (Height): 2.13" (54 mm)
Physical dimensions (Width): 14.66" (372 mm)
Physical dimensions (Depth): 6.96" (177 mm)
Weight: 7.15 lbs (3.6 kg)
Operating voltage: 10-15 VDC
Operating temperature range: –4º to 149º F (–20º to 65º C)
Warranty: 2 years
Audio
Amplifier class: Class D
Rated continuous (RMS) power (14.4 V input @ 4 Ohm < 1% THD): 75 W x 4/150 x 2 200 W x 2/400 W x 1 (Bridged)
Rated continuous (RMS) power (14.4 V input @ 2 Ohm < 1% THD): 100 W x 4/200 x 2
Signal-to-Noise Ratio, referred to highest rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth): Analog Inputs >104 dB
Signal-to-Noise Ratio, referred to 1 W (A-weighted, 20 Hz - 20 kHz noise bandwidth): Analog Inputs >84 dB
Damping factor @ 4 Ω: >150/50 Hz
Damping factor @ 2 Ω: >75/50 Hz
THD+N @ Rated Power: <1% @ 4 Ω
Frequency response (+0, -1dB): 12 Hz-22 kHz
Input voltage range @ RCA inputs: Switchable from 200 mV-2 V RMS (Low) to 800 mV-8 V RMS (High)
Signal Processing
Filter mode(s): Channels 1 & 2: High-pass only (Off, x1, x10)
Filter Slope(s): Channels 1 & 2 12 dB/octave
Filter frequency range: Channels 1 & 2: 50 Hz-500 Hz (x10: 500 Hz-5 kHz)
Filter mode(s): Channels 3 & 4: Off, High-pass or Bandpass
Filter Slope(s): Channels 3 & 4 12 dB/octave
Filter frequency range: Channels 3 & 4 50 Hz-500 Hz
Filter mode(s): Channels 5 & 6: Off, High-pass or Bandpass
Filter Slope(s): Channels 5 & 6: 12 dB/octave
Filter frequency range: Channels 5 & 6: 50 Hz-500 Hz
Detented, calibrated filter frequent potentiometers: Yes
Channel input mode switch: yes (2/4/6 Channels)
Pass-through preamp output: Buffered
2x JL Audio C7-650cw 6.50-inch (165mm) Component Woofer Grille included - (C7-650cw) JL Audio C7-650cw
6.5-inch (165 mm) Component Woofer, Single
Introduction
C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing.
The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviors.
Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance.
C7-650cw Design Notes: Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high frequency behavior.
Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw's outstanding excursion capability.
Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver's performance range.
A 32 mm (1.27 inch) diameter, overhung voice coil is employed, wound with copper wire onto a fiberglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area, and our Patented Elevated Frame Cooling technology.
Design Bandwidth:
Built in USA with Global Components
The performance of every C7 driver is tested and verified, then assigned a unique serial number. Register your C7 loudspeaker online to receive a copy of its specific Acoustical Test Report HERE.
General Specifications
Continuous Power Handling (RMS)
125 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
50 - 175 W / Ch.
Nominal Impedance
4 Ω
Frequency Response
50 Hz - 5 KHz ± 3 dB
Parameters
Voice Coil Resistance (Re)
3.114 Ω
Free Air Resonance (Fs)
54.5 Hz
Reference Efficiency (no)
0.304%
Efficiency
87.0 dB @ 1W / 1m
Sensitivity
90.0 dB @ 2.83V / 1m
Electrical “Q” (Qes)
0.669
Mechanical “Q” (Qms)
6.265
Total Speaker “Q” (Qts)
0.605
Equivalent Compliance (Vas)
0.461 cu. ft. (13.05 liters)
Moving Mass (Mms)
17.679 g
Mechanical Compliance (Cms)
0.000482 m/N
Magnetic Strength (BL)
5.31 N/A
Effective Piston Area (Sd)
21.4 sq. in. (0.013807 sq. m)
One Way Linear Excursion (Xmax)
5 mm
Physical Specifications
Frame Outer Diameter (A)
6.50 in / 165 mm
Bolt Hole Circle Diameter (B)
6.12 in / 155 mm
Mounting Hole Diameter (C)
5.56 in / 141 mm
Grille Tray Outer Diameter (D)
7.20 in / 183 mm
Frontal Grille Protrusion* (E)
0.98 in / 25 mm
Mounting Depth (F)
2.77 in / 70 mm
Motor Outer Diameter (G)
3.94 in / 100 mm
2x JL Audio C7-350cm 3.5-inch (90mm) Component Midrange Driver Grille included - (C7-350cm) JL Audio C7-350cm
3.5-inch (90 mm) Component Midrange, Single
Introduction
C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing.
The C7-350cm component midrange is designed to operate in a 3-way system, with a woofer and tweeter. Conceived and purpose-built from the ground up, it offers exceptional transient response and outstanding linearity, resulting in unsurpassed clarity and natural mid-range reproduction. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviors.
Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance.
C7-350cm Design Notes: Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A concave dust cap further improves high frequency behavior.
Suspension design: The moving assembly is suspended and damped via a linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting excursion.
Motor Design: The C7-350cm employs a high-density magnetic circuit with a high-grade, neodymium magnet, and a specially machined, U-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver's performance range.
A 36 mm (1.42 inch) diameter, overhung voice coil is employed, wound with copper-clad aluminum wire onto a fiberglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels.
Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area.
Design Bandwidth:
Built in USA with Global Components
The performance of every C7 driver is tested and verified, then assigned a unique serial number. Register your C7 loudspeaker online to receive a copy of its specific Acoustical Test Report.
General Specifications
Continuous Power Handling (RMS)
100 W
Peak Music Power
200 W
Recommended Amplifier Power (RMS)
50 - 150 W / Ch.
Nominal Impedance
4 Ω
Frequency Response
300 Hz - 10 KHz ± 3 dB
Parameters
Moving Mass (Mms)
4.009 g
Equivalent Compliance (Vas)
0.015 cu. ft. (0.430 liters)
Mechanical Compliance (Cms)
0.000257 m/N
Magnetic Strength (BL)
4.66 N/A
One Way Linear Excursion (Xmax)
1 mm
Effective Piston Area (Sd)
5.31 sq. in. (0.003426 sq. m)
Total Speaker “Q” (Qts)
0.541
Mechanical “Q” (Qms)
6.454
Reference Efficiency (no)
0.27%
Free Air Resonance (Fs)
156.9 Hz
Efficiency
86.5 dB @ 1W / 1m
Sensitivity
89.5 dB @ 2.83V / 1m
Electrical “Q” (Qes)
0.59
Voice Coil Resistance (Re)
3.245 Ω
Physical Specifications
Frame Outer Diameter (A)
3.45 in / 88 mm
Bolt Hole Circle Diameter (B)
3.15 in / 80 mm
Mounting Hole Diameter (C)
2.87 in / 73 mm
Grille Tray Outer Diameter (D)
3.95 in / 100 mm
Frontal Grille Protrusion (E)
0.58 in / 15 mm
Mounting Depth (F)
1.46 in / 37 mm
Motor Outer Diameter (G)
2.36 in / 60 mm
2x JL Audio C7-100ct 1-inch (19mm) Corundum ceramic-coated, aluminum dome tweeter Grille included - (C7-100ct) JL Audio C7-100ct
1-inch (25 mm) Component Tweeter, Single
Introduction
C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing.
The C7-100ct component tweeter is designed to deliver unparalleled high-frequency performance. Utilizing a corundum ceramic-coated aluminum alloy diaphragm suspended via a treated silk, s-roll surround, it provides spectacularly detailed reproduction of treble frequencies with outstanding off-axis response. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviors.
Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance.
C7-100ct Design Notes: Dome Diaphragm: Corundum ceramic coated aluminum alloy diaphragm exhibits high stiffness, very low mass and excellent environmental stability. It also helps the tweeter dome to hold its shape and operate as a true piston at higher frequencies, without a penalty in moving mass.
Suspension Design: The diaphragm's motion is centered, sprung and damped by a treated silk, s-roll surround. Ferrofluid in the magnetic gap acts as a rear suspension element in this design. The two combine to provide optimum damping without unduly restricting excursion.
Motor Design: The C7-100ct employs a high-density magnetic circuit with a neodymium magnet and U-Yoke motor topology. An under-hung voice coil is employed, wound with copper-clad aluminum wire onto an aluminum voice coil former. Motor magnetics have been precisely optimized utilizing advanced FEA tools to lower even order distortion and IMD/AMD.
Acoustical Design: The shape of the tweeter housing is designed to boost sensitivity in a very specific bandwidth, helping to flatten the frequency response. It also provides improved control of directivity.
Design Bandwidth:
Sold individually, with flush and surface mounting fixtures and hardware. One 15μF tweeter protection capacitor is also included.
The performance of every C7 driver is tested and verified, then assigned a unique serial number. Register your C7 loudspeaker online to receive a copy of its specific Acoustical Test Report.
General Specifications
Continuous Power Handling (RMS)
100 W
Peak Music Power
200 W
Recommended Amplifier Power (RMS)
50 - 150 W / Ch.
Nominal Impedance
4 Ω
Frequency Response
3 kHz - 30 KHz ± 3 dB
Parameters
Voice Coil Resistance (Re)
3.20 Ω
Free Air Resonance (Fs)
1450 Hz
Reference Efficiency (no)
0.267%
Efficiency
86.5 dB @ 1W / 1m
Sensitivity
89.5 dB @ 2.83V / 1m
Physical Specifications
Flush Mount Fixture Diameter (A1)
2.13 in / 54 mm
Surface Mount Fixture Diameter (A2)
2.16 in / 55 mm
Flush Mount Mounting Hole Diameter (B)
1.88 in / 48 mm
Flush Mount Mounting Depth (C)
0.73 in / 19 mm
Flush Mount Tweeter Frontal Protrusion (D1)
0.33 in / 8 mm
Surface Mount Tweeter Frontal Protrusion (D2)
1.06 in / 27 mm
