Description
Included in this kit
This bundle includes a MTX Audio JH7005 Jackhammer Series 90W x 4 & 450W x 1 @ 2-Ohm Full Range Class D 5-Channel Amplifier, and 2x Alpine W10S4 10-inch Single 4 Ohm Subwoofer.
1x MTX Audio JH7005 Jackhammer Series 90W x 4 & 450W x 1 @ 2-Ohm Full Range Class D 5-Channel Amplifier - (JH7005)
MTX JH7005
Jackhammer Series 700 Watt Five Channel Full System Amplifier
Easy Access Controls
The JH7005 is fully loaded and ready to drive an entire system. The top panel includes controls for both full range speakers, gain, crossover and frequency adjustment, as well as controls for the subwoofer output including fully adjustable gain, low pass filter, subsonic filter and bass boost.
Only What You Need
The JH7005 has the functionality to power a complete system including full range speakers and subwoofer(s). The input section features high quality RCAs (front, rear, sub) for easy connection to after market head units or processors. The Input Level selection is either Pre or Spk In so it can also be used with factory radios that don't have RCA outputs. The unit can also be used in either 5-channel, 4-channel or 2-channel modes depending on the Input Mode selection.
High Quality Power and Speaker Connections
The JH7005 can accept up to a standard 1/0-gauge power and ground wire for optimal performance. The speaker terminals can accept up to 12-gauge speaker. Both sets of connectors use set screw style fittings that ensure proper connection and continual signal transfer.
FEATURES ā¢ All-In-One System Design
ā¢ Top Mount Controls
ā¢ Variable Crossovers
ā¢ Selectable Turn On Input
ā¢ Selectable Input Signal
ā¢ Variable Subsonic Filter
ā¢ Remote Bass Knob
SPECIFICATIONS ā¢ Description: 5-Channel
ā¢ Topology: Class AB + D
ā¢ 4Ī© RMS Power Output: 60W X 4 Channel, 275W x 1 Channel
ā¢ 4Ī© Bridged: 180W x 2 Channel
ā¢ 2Ī© RMS Power Output: 90W x 4 Channel, 450W x 1 Channel
ā¢ THD: Less Than 1%
ā¢ Signal to Noise Ratio: 60dB
ā¢ Frequency Response: 20Hz to 20kHz (4 channels), 20Hz - 250Hz (subwoofer)
ā¢ Crossover: 40Hz to 250Hz, 12dB/Oct
ā¢ High Pass Filter: 40Hz to 250Hz, 12dB/Oct
ā¢ Subsonic Filter: 20Hz to 50Hz, 12dB/Oct
ā¢ Bass Boost: 0 - 12dB @ 45Hz
ā¢ Maximum Input Signal: 10V
ā¢ Height: 2.57" (65.2mm)
ā¢ Width: 7.61" (193.4mm)
ā¢ Depth: 15.47" (393mm)
2x Alpine W10S4 10-inch Single 4 Ohm Subwoofer - (W10S4)
Alpine W10S4 10-inch Single 4 Ohm Subwoofer
Overview:
10-inch single 4Ī© subwoofer
Polypropylene and mica cone with poly-foam surround
250W RMS
750W peak power handling
Frequency Response: 30Hz-200Hz
24Hz-200Hz frequency response
5-1/16-inch mounting depth
Recommended Sealed box volume: 0.83 cu. Ft.
Recommended Ported box volume: 1.51 cu. ft
Bass For All
The 2017 BASS subwoofers are engineered to be fun and loud in a budget friendly category by combining retro styling with enough efficiency to run on 250W RMS.
Performance: Efficiency & Tight Bass
An optimized magnet circuit allows more focused magnetism in the gap which results in improved efficiency. This means tighter bass control and more output!