Description
JL Audio JD1000/1:Monoblock Class D Subwoofer Amplifier 1000 W
JD Amplifiers redefine a high-value package in terms of performance and efficiency. JL Audio’s NexD™ switching technology and clipping indicators (for ease in setting Input Sensitivity), add tremendous bang for your buck. Their dual-range, differential-balanced inputs minimize noise, while maximizing compatibility with a wide range of signal levels. Monoblock models also include variable bass boost and Remote Level Control capability when used with an optional RBC-1 Remote Bass Control.
They fit nearly anywhere!JD1000/1: 11.40 x 7.50 x 2.10 in. (290 x 190 x 53 mm). High-mass heat sink improves thermal capacity leading to reduced incidence of shut-down events.
NexD™ Switching Amplifier Technology: Our high-speed switching technology delivers outstanding fidelity with very low noise and distortion. Exceptional efficiency results in reduced current draw and heat, permitting reliable high power output within a very small chassis. Specifically optimized for subwoofer applications (7 Hz - 500 Hz bandwidth).
Complete Signal Processing Package: 12dB/octave low-pass filter, non-defeatable, with fully variable filter frequency selection from 50-500 Hz. Adjustable 0 to +12 dB Bass Boost EQ @ 45 Hz. Remote level control with optional controller (RBC-1). Preamp outputs (buffered, pass-through type)
Dual-Range, Differential-Balanced Inputs and Automatic Turn-On CapabilitiesBenefits: NO NOISE! Outstanding noise rejection prevents alternator whine and other noises. Accepts line-level or speaker level signals (up to 8V RMS), including those from factory systems, without a line-output converter (LOC): just splice wires to a pair of RCA ends or RCA cables. Automatic turn-on option via Signal-Sensing or DC-Offset sensing
Integrated LED Clipping Indicator for Easy Setup: Simplifies input-sensitivity setting by providing accurate visual feedback of output clipping level.1) Disconnect one speaker output wire, 2) Play full-scale (0 dBfs) sine-wave through audio system, with head unit at 3/4 volume and tone controls set flat, 3) Adjust input sensitivity until light turns on, then back off slightly. Separate, top-mounted LEDs report overall status and condition
Rated Continuous (RMS) Power @ 14.4 V
| @ 4 Ω | 600 W RMS x 1 |
| @ 3 Ω | 800 W RMS x 1 |
| @ 2 Ω | 1000 W RMS x 1 |
| @ 1.5 Ω | N/A |
General Specifications
| Dimensions | 11.40 x 7.50 x 2.10 in. (290 x 190 x 53 mm) |
| Frequency Response | 20 Hz - 150 kHz (+0, -1dB) |
| S/N Ratio, referred to highest rated power | >75 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| S/N Ratio, referred to 1 W | >45 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| Damping Factor @ 4 Ω | >1000 / 50 Hz |
| Damping Factor @ 2 Ω | >500 / 50 Hz |
| THD+N @ Rated Power | <1% @ 2 Ω per Ch. |
| Input Voltage Range @ RCA Inputs | 2 V - 10 V RMS |
| Input Voltage Range @ RCA Inputs | 200 mV - 4 V RMS |
| Min.Copper Power / Ground Wire Gauge | 4 AWG wire |
| Fuse Rating | 80 A (AFS, AGU or MaxiFuse™) |
Signal Processing
| Filter Mode(s) | Low-Pass only |
| Filter Slope(s) | 12 dB/octave |
| Filter Frequency Range | 50 Hz - 200 Hz |
| Detented, Calibrated Filter Freq. Potentiometer | No |
| Filter Defeat Function | No |
| Infrasonic Filter | none |
| Bass Boost EQ | 0 to +12 dB @ 45 Hz |
| Output Polarity Switch | No |
| Remote Subwoofer Level Control | Optional (RBC-1) |
| Remote Bass EQ Boost Control | No |
| Pass-Through Preamp Output | Buffered |