Description
Included in this kit
This bundle includes a Wet Sounds WWX-POL-RC-ADAP Adapter for Polaris Ride Command, and a JL Audio MX280/4 4 Channel 280 watt, Marine/Power Sports grade amplifier.
1x Wet Sounds WWX-POL-RC-ADAP Adapter for Polaris Ride Command - (WWX-POL-RC-ADAP)
So, you bought a 2017 Polaris that is Ride Command equipped and canāt figure out how to add more audio to the factory system. Well now you donāt have to worry. The Polaris Ride Command Adaptor from Wet Sounds adapts the factory Ride Command plug from the rear of the Polaris Ride Command to a pair of female RCA connectors, allowing Ride Command to run an audio signal output from Ride Command to an input of a Wet Sounds Soundbar, AS-Series Powered Sub, and/or an aftermarket amplifier. A blue remote turn-on wire is also included to power on an aftermarket amplifier and/or Stealth AS-Series Sub when Ride Command is powered up.
This adapter is compatible with any audio equipment that supports an audio input via RCA connectors.
1x JL Audio MX280/4 4 Channel 280 watt, Marine/Power Sports grade amplifier - (MX280/4)
JL Audio MX280/4
Engineered specifically for powersports applications, the 4-channel MX280/4 amplifier employs our high-speed NexDā¢ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX6 water-resistance rating, making it perfect for motorcycles, ATVās or other utility vehicles.
Generating a solid 50W x 4 into 4 ohms (14.4V, 1% THD), the MX280/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 140W x 2 into 4 ohms.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
Rated Continuous (RMS) Power @ 14.4 V
| @ 4 Ī© | 50 W RMS x 4 |
| @ 2 Ī© | 70 W RMS x 4 |
| Bridged @ 4Ī© | 140 W RMS x 2 |
Rated Continuous (RMS) Power @ 12.5 V
| @ 4 Ī© | 36 W RMS x 4 |
| @ 2 Ī© | 52 W RMS x 4 |
| Bridged @ 4Ī© | 100 W RMS x 2 |
General Specifications
| Frequency Response | 20 Hz - 20 kHz (+0, -1dB) |
| S/N Ratio, referred to highest rated power | >89.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| S/N Ratio, referred to 1 W | >68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| Damping Factor @ 4 Ī© | >60 / 50 Hz |
| Damping Factor @ 2 Ī© | >30 / 50 Hz |
| THD+N @ Rated Power | <1% @ 2 Ī© per Ch. |
| Input Voltage Range @ RCA Inputs | Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) |
| Min.Copper Power / Ground Wire Gauge | 8 AWG wire |
| Fuse Rating | 35 A (AFS, AGU or MaxiFuseā¢) |
Signal Processing
| Filter Mode(s) | Low-Pass or High-Pass |
| Filter Slope(s) | 12 dB/octave |
| Filter Frequency Range | 35 Hz - 300 Hz |
| Detented, Calibrated Filter Freq. Potentiometers | Yes |
| Filter Defeat Function | Yes |
| Remote Level Control | No |
| Remote Level Modes | N/A |
| Channel Input Mode Switch | Yes (2/3/4 ch.) |
| Pass-Through Preamp Output | None |
| Source Channel Selection for PreOuts | N/A |
Physical Specifications
| Height (H) | 1.77 in / 45 mm |
| Width (W) | 8.66 in / 220 mm |
| Depth (D) | 3.09 in / 78.5 mm |
| Net Weight | 3.18 lb / 1.44 kg |