Description
Included in this kit
This bundle includes a Wet Sounds WWX-POL-RC-ADAP Adapter for Polaris Ride Command, and a JL Audio MX300/1 300 watt mono block, Marine/Power Sports grade amplifier.
1x Wet Sounds WWX-POL-RC-ADAP Adapter for Polaris Ride Command - (WWX-POL-RC-ADAP)
So, you bought a 2017 Polaris that is Ride Command equipped and can’t figure out how to add more audio to the factory system. Well now you don’t have to worry. The Polaris Ride Command Adaptor from Wet Sounds adapts the factory Ride Command plug from the rear of the Polaris Ride Command to a pair of female RCA connectors, allowing Ride Command to run an audio signal output from Ride Command to an input of a Wet Sounds Soundbar, AS-Series Powered Sub, and/or an aftermarket amplifier. A blue remote turn-on wire is also included to power on an aftermarket amplifier and/or Stealth AS-Series Sub when Ride Command is powered up.
This adapter is compatible with any audio equipment that supports an audio input via RCA connectors.
1x JL Audio MX300/1 300 watt mono block, Marine/Power Sports grade amplifier - (MX300/1)
JL Audio MX300/1
Engineered specifically for powersports applications, the MX300/1 monoblock amplifier employs our high-speed NexD™ switching design to pack a serious audio punch, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX6 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
With a robust 300W of clean power into a 2-ohm load (14.4V, 1% THD), use one to drive a subwoofer, or grab a pair to deliver stunning output to a subwoofer system. The MX300/1 also features an adjustable low-pass crossover, a bass boost EQ, variable infrasonic filter and output polarity switch.
Its dual-range input section accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals. With the addition of an M-RBC-1 remote level control (sold separately), subwoofer output can be directly controlled from the driver’s seat.
Rated Continuous (RMS) Power @ 14.4 V
| @ 4 Ω | 160 W RMS x 1 |
| @ 3 Ω | 220 W RMS x 1 |
| @ 2 Ω | 300 W RMS x 1 |
| @ 1.5 Ω | N/A |
Rated Continuous (RMS) Power @ 12.5 V
| @ 4 Ω | 160 W RMS x 1 |
| @ 3 Ω | 200 W RMS x 1 |
| @ 2 Ω | 250 W RMS x 1 |
| @ 1.5 Ω | N/A |
General Specifications
| Frequency Response | 20 Hz - 12 kHz (+0, -1dB) |
| S/N Ratio, referred to highest rated power | >85 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| S/N Ratio, referred to 1 W | >64 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| Damping Factor @ 4 Ω | >150 / 50 Hz |
| Damping Factor @ 2 Ω | >75 / 50 Hz |
| THD+N @ Rated Power | <1% @ 2 Ω |
| Input Voltage Range @ RCA Inputs | Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) |
| Min.Copper Power / Ground Wire Gauge | 8 AWG wire |
| Fuse Rating | 30 A (AFS, AGU or MaxiFuse™) |
Signal Processing
| Filter Mode(s) | Low-Pass only |
| Filter Slope(s) | 24 dB/octave |
| Filter Frequency Range | 40 Hz - 400 Hz |
| Detented, Calibrated Filter Freq. Potentiometer | Yes |
| Filter Defeat Function | Yes |
| Infrasonic Filter | 20 Hz - 40 Hz, variable |
| Bass Boost EQ | 0 to +12 dB @ 43 Hz |
| Output Polarity Switch | Yes |
| Remote Subwoofer Level Control | Optional (M-RBC-1) |
| Remote Bass EQ Boost Control | No |
| Pass-Through Preamp Output | None |
Physical Specifications
| Height (H) | 1.77 in / 45 mm |
| Width (W) | 8.66 in / 220 mm |
| Depth (D) | 3.09 in / 78.5 mm |
| Net Weight | 3.18 lb / 1.44 kg |