Description
Included in this kit
This bundle includes a Wet Sounds WWX-POL-RC-ADAP Adapter for Polaris Ride Command, a JL Audio MX280/4 4 Channel 280 watt, Marine/Power Sports grade amplifier, a JL Audio SB-POL-GNRLSPKR/M3-650i Stealthbox Speaker Pods for 2016+ Polaris General, and a Clarion CMR-L1 Marine LED Light Controller.
1x Wet Sounds WWX-POL-RC-ADAP Adapter for Polaris Ride Command - (WWX-POL-RC-ADAP)
So, you bought a 2017 Polaris that is Ride Command equipped and can’t figure out how to add more audio to the factory system. Well now you don’t have to worry. The Polaris Ride Command Adaptor from Wet Sounds adapts the factory Ride Command plug from the rear of the Polaris Ride Command to a pair of female RCA connectors, allowing Ride Command to run an audio signal output from Ride Command to an input of a Wet Sounds Soundbar, AS-Series Powered Sub, and/or an aftermarket amplifier. A blue remote turn-on wire is also included to power on an aftermarket amplifier and/or Stealth AS-Series Sub when Ride Command is powered up.
This adapter is compatible with any audio equipment that supports an audio input via RCA connectors.
1x JL Audio MX280/4 4 Channel 280 watt, Marine/Power Sports grade amplifier - (MX280/4)
JL Audio MX280/4
Engineered specifically for powersports applications, the 4-channel MX280/4 amplifier employs our high-speed NexD™ switching design to deliver plenty of clean power, without straining charging systems. Its tiny, cast aluminum chassis is highly resistant to corrosion, with an IPX6 water-resistance rating, making it perfect for motorcycles, ATV’s or other utility vehicles.
Generating a solid 50W x 4 into 4 ohms (14.4V, 1% THD), the MX280/4 is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a potent 140W x 2 into 4 ohms.
Other features include independent front and rear crossovers with selectable full-range, high-pass or low-pass filter controls and a dual-range input section that accepts a wide range of input voltage levels, from line-level all the way to high-power speaker level signals.
Rated Continuous (RMS) Power @ 14.4 V
| @ 4 Ω | 50 W RMS x 4 |
| @ 2 Ω | 70 W RMS x 4 |
| Bridged @ 4Ω | 140 W RMS x 2 |
Rated Continuous (RMS) Power @ 12.5 V
| @ 4 Ω | 36 W RMS x 4 |
| @ 2 Ω | 52 W RMS x 4 |
| Bridged @ 4Ω | 100 W RMS x 2 |
General Specifications
| Frequency Response | 20 Hz - 20 kHz (+0, -1dB) |
| S/N Ratio, referred to highest rated power | >89.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| S/N Ratio, referred to 1 W | >68 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| Damping Factor @ 4 Ω | >60 / 50 Hz |
| Damping Factor @ 2 Ω | >30 / 50 Hz |
| THD+N @ Rated Power | <1% @ 2 Ω per Ch. |
| Input Voltage Range @ RCA Inputs | Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High) |
| Min.Copper Power / Ground Wire Gauge | 8 AWG wire |
| Fuse Rating | 35 A (AFS, AGU or MaxiFuse™) |
Signal Processing
| Filter Mode(s) | Low-Pass or High-Pass |
| Filter Slope(s) | 12 dB/octave |
| Filter Frequency Range | 35 Hz - 300 Hz |
| Detented, Calibrated Filter Freq. Potentiometers | Yes |
| Filter Defeat Function | Yes |
| Remote Level Control | No |
| Remote Level Modes | N/A |
| Channel Input Mode Switch | Yes (2/3/4 ch.) |
| Pass-Through Preamp Output | None |
| Source Channel Selection for PreOuts | N/A |
Physical Specifications
| Height (H) | 1.77 in / 45 mm |
| Width (W) | 8.66 in / 220 mm |
| Depth (D) | 3.09 in / 78.5 mm |
| Net Weight | 3.18 lb / 1.44 kg |
1x JL Audio SB-POL-GNRLSPKR/M3-650i Stealthbox Speaker Pods for 2016+ Polaris General - (SB-POL-GNRLSPKR/M3-650i)
JL Audio SB-POL-GNRLSPKR/M3-650i Stealthbox Speaker Pods for 2016+ Polaris General
The Polaris General is built to take command of any off-road or backcountry trail you can throw at it. Unfortunately, its factory audio options are too weak to keep up with the challenges of an open-air cockpit.
Purpose-built for two seat and four seat Polaris General vehicles, these custom-engineered speaker pods are constructed from 100% fiberglass with a rugged weatherproof finish and mount securely in each kick-panel, off the floor and out of the way. Each sealed enclosure houses a high-performance, M3 6.5-inch marine coaxial speaker and delivers powerful, crystal-clear sound to add more excitement to all your outdoor adventures.
Best used in conjunction with JL Audio's Stealthbox® subwoofer system designed for the General.
The Hard Data: Contains one pair of M3-650x-S-Gm-i marine coaxial speakers with RGB LED illumination, each in a sealed, fiberglass enclosure. 60 watt power handling (per channel). 4 ohms per channel. Installs in kick-panels.
1x Clarion CMR-L1 Marine LED Light Controller - (CMR-L1)
The Clarion CMR-L1 Marine LED light controller adds some flair to Clarion and other RGB LED marine speakers!
Specifications:
• Dynamic Modes 20
• Dynamic Speed Levels 10
• Static Colors 20
• Direct Preset Colors 7
• Brightness Levels 8
• Operating Voltage 10- 15V DC
• Operating Temp Range -4 ° F to + 1 58 ° F, (-20 °C to + 70 °C)
• Operating Frequency 433.92 MHz
• Operating Range* Up to 15 m (49.2 ft)
• Output Capacity 2 A (maximum)
• Recommended Fuse Value 10 A (maximum)
• Dimensions 2. 99 in x 2 in x 1 .07 in
• (Transmitter) 76 mm x 50.8 mm x 27.2 mm
• Dimensions 4.02 in x 3.01 in x 1.42 in
• (Receiver) 102.1 mm x 76.5 mm x 36.1 mm
Notes:
• Install in a dry, well-ventilated location; do not install in an engine compartment or other areas of extreme heat. Do not install where it will be directly exposed to the elements.
• To optimize performance, avoid confined installation locations or areas surrounded by metal; maintain at least 25 cm (10 in) of separation from any audio signal cables.
• Make sure the total amperage demands of all connected LED circuits does not exceed the output capacity of the controller.
• *Install a fuse (not included) at the main +12V power wire (Red) connection point that is appropriate for the total current draw of all LED circuits (up to 10 A).
• For short-circuit protection, we recommend installing a fuse (not included) at EACH speaker's +12V LED connection lead. Refer to your speaker's LED specifications for individual fuse values.