Description
Included in this kit
This bundle includes a JL Audio JD1000/1 Monoblock Class-D Subwoofer Amplifier, 1000 W, and 2x JL Audio 10TW1-4: 10-inch (250 mm) Subwoofer Driver 4 Ohm - Open Box.
1x JL Audio JD1000/1 Monoblock Class-D Subwoofer Amplifier, 1000 W (JD1000/1)
JL Audio JD1000/1:Monoblock Class D Subwoofer Amplifier 1000 W
JD Amplifiers redefine a high-value package in terms of performance and efficiency. JL Audio’s NexD™ switching technology and clipping indicators (for ease in setting Input Sensitivity), add tremendous bang for your buck. Their dual-range, differential-balanced inputs minimize noise, while maximizing compatibility with a wide range of signal levels. Monoblock models also include variable bass boost and Remote Level Control capability when used with an optional RBC-1 Remote Bass Control.
They fit nearly anywhere!JD1000/1: 11.40 x 7.50 x 2.10 in. (290 x 190 x 53 mm). High-mass heat sink improves thermal capacity leading to reduced incidence of shut-down events.
NexD™ Switching Amplifier Technology: Our high-speed switching technology delivers outstanding fidelity with very low noise and distortion. Exceptional efficiency results in reduced current draw and heat, permitting reliable high power output within a very small chassis. Specifically optimized for subwoofer applications (7 Hz - 500 Hz bandwidth).
Complete Signal Processing Package: 12dB/octave low-pass filter, non-defeatable, with fully variable filter frequency selection from 50-500 Hz. Adjustable 0 to +12 dB Bass Boost EQ @ 45 Hz. Remote level control with optional controller (RBC-1). Preamp outputs (buffered, pass-through type)
Dual-Range, Differential-Balanced Inputs and Automatic Turn-On CapabilitiesBenefits: NO NOISE! Outstanding noise rejection prevents alternator whine and other noises. Accepts line-level or speaker level signals (up to 8V RMS), including those from factory systems, without a line-output converter (LOC): just splice wires to a pair of RCA ends or RCA cables. Automatic turn-on option via Signal-Sensing or DC-Offset sensing
Integrated LED Clipping Indicator for Easy Setup: Simplifies input-sensitivity setting by providing accurate visual feedback of output clipping level.1) Disconnect one speaker output wire, 2) Play full-scale (0 dBfs) sine-wave through audio system, with head unit at 3/4 volume and tone controls set flat, 3) Adjust input sensitivity until light turns on, then back off slightly. Separate, top-mounted LEDs report overall status and condition
Rated Continuous (RMS) Power @ 14.4 V
| @ 4 Ω | 600 W RMS x 1 |
| @ 3 Ω | 800 W RMS x 1 |
| @ 2 Ω | 1000 W RMS x 1 |
| @ 1.5 Ω | N/A |
General Specifications
| Dimensions | 11.40 x 7.50 x 2.10 in. (290 x 190 x 53 mm) |
| Frequency Response | 20 Hz - 150 kHz (+0, -1dB) |
| S/N Ratio, referred to highest rated power | >75 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| S/N Ratio, referred to 1 W | >45 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) |
| Damping Factor @ 4 Ω | >1000 / 50 Hz |
| Damping Factor @ 2 Ω | >500 / 50 Hz |
| THD+N @ Rated Power | <1% @ 2 Ω per Ch. |
| Input Voltage Range @ RCA Inputs | 2 V - 10 V RMS |
| Input Voltage Range @ RCA Inputs | 200 mV - 4 V RMS |
| Min.Copper Power / Ground Wire Gauge | 4 AWG wire |
| Fuse Rating | 80 A (AFS, AGU or MaxiFuse™) |
Signal Processing
| Filter Mode(s) | Low-Pass only |
| Filter Slope(s) | 12 dB/octave |
| Filter Frequency Range | 50 Hz - 200 Hz |
| Detented, Calibrated Filter Freq. Potentiometer | No |
| Filter Defeat Function | No |
| Infrasonic Filter | none |
| Bass Boost EQ | 0 to +12 dB @ 45 Hz |
| Output Polarity Switch | No |
| Remote Subwoofer Level Control | Optional (RBC-1) |
| Remote Bass EQ Boost Control | No |
| Pass-Through Preamp Output | Buffered |
2x JL Audio 10TW1-4: 10-inch (250 mm) Subwoofer Driver 4 Ohm - Open Box (10TW1-4-UOB-K)
JL Audio 10TW1-4
TW1 10-inch Subwoofer Driver (300 W, 4 Ω)
Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design.
JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs.
The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth.
Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch subwoofer driver, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system.
- Very shallow mounting depth (4.36 in / 111 mm)
- No pole vent: permits mounting close to rear wall of enclosure
- Extremely small sealed enclosure volume requirements
- Long linear excursion capability (0.40 in / 10 mm, one-way)
- DMA-optimized motor design
- Patented "concentric tube" architecture
- Patented "floating cone attach method" technology
- Cast alloy frame with flat edges for tight driver grouping
- Injection molded, mica-filled polypropylene cone
- Rubber surround
- Steel mesh grille included with each driver
- Precision-built in USA with Global Copmonents at JL Audio's Miramar, Florida factory
General Specifications
| Continuous Power Handling (RMS) | 300 W |
| Recommended Amplifier Power (RMS) | 75 - 300 W |
| Nominal Impedance (Znom) | 4 Ω |
Physical Specifications
| Nominal Diameter | 10.0 in / 250 mm |
| Overall Diameter (A) | 10.375 in / 264 mm |
| Mounting Hole Diameter (B) | 9.0625 in / 230 mm |
| Bolt Hole Circle Diameter (C) | 9.7 in / 246 mm |
| Motor Outer Diameter (D) | 4.54 in / 115 mm |
| Mounting Depth (E) | 4.36 in / 111 mm |
| Front Grille Protrusion (F) | 0.87 in / 22 mm |
| Driver Displacement | 0.047 cu ft / 1.33 L |
| Net Weight | 10.5 lb / 4.8 kg |
Parameters
| Free Air Resonance (Fs) | 41.45 Hz |
| Electrical “Q” (Qes) | 0.696 |
| Mechanical “Q” (Qms) | 9.7 |
| Total Speaker “Q” (Qts) | 0.649 |
| Equivalent Compliance (Vas) | 0.364 cu ft / 10.31 L |
| One-Way Linear Excursion (Xmax)* | 0.40 in / 10.0 mm |
| Efficiency (1 W / 1 m)** | 82.5 dB SPL |
| Effective Piston Area (Sd) | 41.602 sq in / 0.0268 sq m |
| DC Resistance (Re) | 3.516 Ω |
Sealed Enclosure Specifications
| Wall Thickness | 0.75 in / 19 mm |
| Front Baffle Thickness | 0.75 in / 19 mm |
| Volume (net int.) | 0.35 cu ft / 9.91 L |
| External Width (W) | 16.125 in / 410 mm |
| External Height (H) | 14 in / 356 mm |
| External Depth (D) | 5.25 in / 133 mm |
| F3 | 48.31 Hz |
| Fc | 59.21 Hz |
| Qtc | 0.927 |
Ported Enclosure Specifications
| Wall Thickness | 0.75 in / 19 mm |
| Front Baffle Thickness | 0.75 in / 19 mm |
| Volume (net int.) | 0.625 cu ft / 17.7 L |
| External Width (W) | 26.625 in / 676 mm |
| External Height (H) | 16 in / 406 mm |
| External Depth (D) | 5.25 in / 133 mm |
| Internal Slot Port Width (SW) | 3.75 in / 95 mm |
| Internal Slot Port Height (SH) | 1.875 in / 48 mm |
| Internal Slot Port Length (SL) | 22.50 in / 572 mm |
| Port Extension Length (EL) | 20.8125 in / 529 mm |
| Tuning Frequency (Fb) | 35.0 Hz |
| F3 | 30.56 Hz |
Used Frequently Asked Questions
- What does used mean? Used products may be unused customer returns that are essentially "new" items, or they may be previously installed products that were returned under warranty or during our return policy period.
- What is the warranty? All of our used items come with a 90-day warranty.
- What's it look like? All of our used items are inspected and graded by our returns team at our facilities. They will test them and grade them to one of four standard gradings: Used Open Box, Used Very Good, Used Good, and Used Acceptable. Please see the following descriptions of each grade - also note that if an item falls under ANY of the criteria for a certain grade, even though the rest of the product is better, we will give it the lowest grade.
- Used Open Box An item in perfect working condition. Original protective wrapping may be missing, but the original packaging is intact and in good condition with minor damage possible. Instructions are included.
- Used Very Good A well-cared-for item with limited use, remains in good working condition. The item may show some limited signs of wear,small scratches,cosmetic blemishes. Item may arrive with damaged packaging or be repackaged and could be missing some accessories.
- Used Good The item shows wear from use, remains in good condition and functions properly. May have damaged packaging or be repackaged. It may be marked, have identifying markings on it, have minor cosmetic damage. It may be missing some parts or accessories.
- Used Acceptable The item is fairly worn but continues to function properly. While repackaged; signs of wear can include aesthetic issues; scratches, dents. The item may have markings on it or show signs of previous use. Item may be missing some parts or accessories.
- Have more questions? Call us, send us a chat, or an email. We'll be able to answer any additional questions you may have.