Description
Included in this kit
This bundle includes a JL Audio 10W7AE-3: 10-inch (250 mm) Subwoofer Driver 3 Ohm, and a JL Audio SGR-10W7:Aluminum Bar Grille set of three.
1x JL Audio 10W7AE-3: 10-inch (250 mm) Subwoofer Driver 3 Ohm (10W7AE-3)
10W7AE-3
10th Anniversary Edition - W7 10-inch Subwoofer Driver (750 W, 3 Ω)
If you are seeking reference-grade sub-bass from a 10-inch driver, your search ends here. Total Car Audio in the UK called it like this when they reviewed the 10W7: "This gives an all round performance of such high quality on every level, that bettering it will be very hard to achieve." Not only does the 10W7 deliver amazing excursion capability for its size, but it also maintains complete composure under power and is able to track complex bass material with uncanny accuracy and power.
The 10W7AE is best used with amplifier power in the 300W - 750W range and is optimized to operate in a 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.5 cu. ft. (42.5 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab.
W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences:
- Satin-Black Powdercoated Baskets
- Bright Anodized Surround Clamp Ring
- Anniversary Edition Cone Badge
- Anniversary Edition Terminal Label
General Specifications
| Continuous Power Handling (RMS) | 750 W |
| Recommended Amplifier Power (RMS) | 300 - 750 W |
| Nominal Impedance (Znom) | 3 Ω |
Physical Specifications
| Nominal Diameter | 10.0 in / 250 mm |
| Overall Diameter (A) | 10.5 in / 267 mm |
| Mounting Hole Diameter (B) | 8.74 in / 222 mm |
| Bolt Hole Circle Diameter (C) | 9.34 in / 237 mm |
| Motor Outer Diameter (D) | 6.55 in / 166 mm |
| Mounting Depth (E) | 8.0 in / 203 mm |
| Driver Displacement | 0.09 cu ft / 2.5 L |
| Net Weight | 30 lb / 13.6 kg |
Parameters
| Free Air Resonance (Fs) | 30.6 Hz |
| Electrical “Q” (Qes) | 0.578 |
| Mechanical “Q” (Qms) | 7.647 |
| Total Speaker “Q” (Qts) | 0.537 |
| Equivalent Compliance (Vas) | 1.28 cu ft / 36.1 L |
| One-Way Linear Excursion (Xmax)* | 0.9 in / 23 mm |
| Reference Efficiency (no) | 0.17% |
| Efficiency (1 W / 1 m)** | 84.3 dB SPL |
| Effective Piston Area (Sd) | 59.8 sq in / 0.0386 sq m |
| DC Resistance (Re) | 2.75 Ω |
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.
Sealed Enclosure Specifications
| Wall Thickness | 0.75 in / 19 mm |
| Front Baffle Thickness | 1.0 in / 25 mm |
| Volume (net int.) | 1.25 cu ft / 35.4 L |
| External Width (W) | 14.5 in / 368 mm |
| External Height (H) | 14.5 in / 368 mm |
| External Depth (D) | 15.375 in / 391 mm |
| F3 | 40.5 Hz |
| Fc | 43.5 Hz |
| Qtc | 0.764 |
Enclosure Notes
Net volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects.
* The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.
The dimensions given for the enclosure examples above take all applicable displacements into consideration
Safety Notice
It is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.
Ported Enclosure Specifications
| Wall Thickness | 0.75 in / 19 mm |
| Front Baffle Thickness | 1.0 in / 25 mm |
| Volume (net int.) | 1.5 cu ft / 42.5 L |
| External Width (W) | 21.75 in / 552 mm |
| External Height (H) | 14.5 in / 368 mm |
| External Depth (D) | 14.625 in / 371 mm |
| Internal Slot Port Width (SW) | 1.5 in / 38 mm |
| Internal Slot Port Height (SH) | 13 in / 330 mm |
| Internal Slot Port Length (SL) | 24.375 in / 619 mm |
| Port Extension Length (EL) | 9 in / 229 mm |
| Tuning Frequency (Fb) | 35.3 Hz |
| F3 | 29.9 Hz |
Enclosure Notes
Net volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects.
* The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.
The dimensions given for the enclosure examples above take all applicable displacements into consideration
Safety Notice
It is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.
1x JL Audio SGR-10W7:Aluminum Bar Grille set of three (SGR-10W7-ROD-RP)
JL Audio SGR-10W7: Aluminum Bar Grille set of three
Set of three aluminum bars to protect one 10W7 subwoofer.
This stylish bar grille system provides sturdy protection to your subwoofer driver and is made from solid brushed aluminum rod stock. The included template makes it a snap to drill your enclosure's woofer baffle to receive the rods.
Fits: 10W7, 10W7AE, 10W7-AE-LP