Description
Hifonics GA-3000.1D GOLIATH 3000 Watt Mono 1-Ohm Stable Amplifier.
LOW NOISE PRE-AMPLIFIER CIRCUITRY
Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion
RCA INPUTS
Nickel-plated RCA jacks create the most effiecient audio connection and resist corrosion
OPERATION MODE
Mono only
CROSSOVER TYPE
Internal crossovers networks allow for audiophile control of equalization circuits
ELECTRONIC EQUALIZER
Control of amplifier output with on-board electronic crossover to tailor specific frequencies to speakers and subwoofers.
LED SYSTEM PROTECTION CIRCUITRY DIAGNOSTICS
Monitor overload and speaker short protection with illuminated indicators on the amplifier end panel
BASS REMOTE INCLUDED
Wired Bass Remote allows adjustments to bass frequencies from the control which can be mounted anywhere in the vehicle.
HEAT SINK
Classic aluminum Hifonics design to minimize heat build up on the Ultra-Fi™ output devices
POWER SUPPLY
Simpatico Coil Design
The dual coil Pulse Width Modulated power supply keeps voltage constant through the Ultra-Fi output devices
Specificaitions:
CLASS - Super D Class
VARIABLE VOLTAGE - 9V - 0.2V
SIGNAL TO NOISE - >95dB
FREQUENCY RESPONSE - 10Hz-50KHz
CROSSOVER - Variable Electronic
VARIABLE LOW PASS CROSSOVER 12DB PER OCTAVE - 30Hz - 250Hz
BASS BOOST - 0 - 10dB
SUBSONIC FILTER - 15Hz - 35Hz
PHASE SHIFT - 0-180°
POWER @ 1 OHM - 1 x 3000
POWER @ 2 OHMS - 1 x 1500 Watts
POWER @ 4 OHMS - 1 x 750 Watts
TOTAL CHANNELS - Mono Only
AUDIO INPUTS - RCA
AUDIO OUTPUTS - 1 Pair
Full Range - RCA
POWER TERMINAL 12V/GND - 0 AWG
SPEAKER TERMINAL WIRE GAUGE - 10 AWG
FUSING - USE EXTERNAL 225 AMP FUSE
TOTAL HARMONIC DISTORTION (THD) - <0.10%
LOW NOISE PRE-AMPLIFIER CIRCUITRY
Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion
RCA INPUTS
Nickel-plated RCA jacks create the most effiecient audio connection and resist corrosion
OPERATION MODE
Mono only
CROSSOVER TYPE
Internal crossovers networks allow for audiophile control of equalization circuits
ELECTRONIC EQUALIZER
Control of amplifier output with on-board electronic crossover to tailor specific frequencies to speakers and subwoofers.
LED SYSTEM PROTECTION CIRCUITRY DIAGNOSTICS
Monitor overload and speaker short protection with illuminated indicators on the amplifier end panel
BASS REMOTE INCLUDED
Wired Bass Remote allows adjustments to bass frequencies from the control which can be mounted anywhere in the vehicle.
HEAT SINK
Classic aluminum Hifonics design to minimize heat build up on the Ultra-Fi™ output devices
POWER SUPPLY
Simpatico Coil Design
The dual coil Pulse Width Modulated power supply keeps voltage constant through the Ultra-Fi output devices
Specificaitions:
CLASS - Super D Class
VARIABLE VOLTAGE - 9V - 0.2V
SIGNAL TO NOISE - >95dB
FREQUENCY RESPONSE - 10Hz-50KHz
CROSSOVER - Variable Electronic
VARIABLE LOW PASS CROSSOVER 12DB PER OCTAVE - 30Hz - 250Hz
BASS BOOST - 0 - 10dB
SUBSONIC FILTER - 15Hz - 35Hz
PHASE SHIFT - 0-180°
POWER @ 1 OHM - 1 x 3000
POWER @ 2 OHMS - 1 x 1500 Watts
POWER @ 4 OHMS - 1 x 750 Watts
TOTAL CHANNELS - Mono Only
AUDIO INPUTS - RCA
AUDIO OUTPUTS - 1 Pair
Full Range - RCA
POWER TERMINAL 12V/GND - 0 AWG
SPEAKER TERMINAL WIRE GAUGE - 10 AWG
FUSING - USE EXTERNAL 225 AMP FUSE
TOTAL HARMONIC DISTORTION (THD) - <0.10%