Complete, five-channel powered sound system upgrade package

The package includes two sets of 6.5” weather-resistant mid-bass drivers and 1” weather-resist tweeters that replace the front and rear soundbar factory speakers, an 8” powered, compact subwoofer, and a 4-channel power pack amplifier.

The weather-resistant speakers are designed for powerful, top-off performance that’s unhindered by weather, wind, or other noise while driving.

The 6.5” mid-bass drivers bring out the full potential of your sound, while the tweeters capture the high frequencies often lost in music reproduction.

The 8” compact subwoofer adds deep, accurate bass that grounds your sound system.

Vehicle-specific speaker connectors and pods designed for the 2018 - Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator are included for plug-and-play installation.

Tweeter adapter plates use the original factory tweeter locations to take the guesswork out of installation.

Vehicle-specific mounting brackets are included to secure the 8” compact subwoofer and 4-channel amplifier under the passenger seat without drilling.

• The PSS-24WRA is a 300-Watt Complete Sound System Upgrade Package for the four-door, non-amplified 2018 – Up Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator.
• The PSS-24WRA is compatible with the i407-WRA-JL 7-Inch Multimedia Receiver and X409-WRA-JL 9-Inch Weather-Resistant Navigation System with Off-Road Mode.
• The PSS-24WRA also includes a vehicle-specific T-harness for installation with the factory radio into a compatible four-door, non-amplified NEW 2018 – 2020 Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator.
• The PSS-24WRA has 5-channels of powered sound that replace your factory system.

Front (SPV-65X-WRA):

• Power handling: 75 watts RMS (225 watts peak)
• Compatible with four-door, non-amplified 2018 - Up Jeep® Wrangler and non-amplified 2020 – Up Jeep® Gladiator
• Frequency response: 65kHz – 22kHz
• Nominal impedance: 4 ohms
• Weather-resistant: IP55

Rear (SPV-65-JLT):

• Power handling: 90 watts RMS (270 watts peak)
• Frequency response: 50kHz – 22kHz
• Nominal impedance: 4 ohms
• SPV-65-JLT weather-resistant rear soundbar speaker system
• Weather-resistant: IP55

Powered Subwoofer (PWE-S8):

• 120 watts RMS (240 watts peak)
• Includes Alpine’s SPV-65X-WRA, SPV-65-JLT, PWE-S8, and KTP-445U
• Frequency response: 32 - 150Hz
• Variable low-pass crossover (80-200 Hz)
• Variable phase control (0-180 degrees)
• preamp- and speaker-level inputs

Four Channel Power Pack Amplifier (KTP-445U):

• 45 watts RMS x 4 at 4 or 2 ohms
• Rugged, premium grills designed to emulate the factory look and appeal
• 90 watts RMS x 2 bridged at 4 ohms
• Selectable high-pass filters (60, 80, or 120 Hz at 12 dB/octave)
• Switchable RCA or speaker-level inputs
• Package Dimensions: 27” L x 18.5” W x 19.5” H, 40lbs

Included:

• KTP-445U Universal 4-Channel Power Amplifier
• PWE-S8 8" Compact Powered Subwoofer
• SPV-65X-WRA Front Component Speakers
• SPV-65-JLT Rear Sound Bar Speakers
• ALP-POD-JLT Front Speaker Pod
• PSU-BKT-JL-R PWE Right Bracket JL
• PSU-BKT-JL-L PWE Left Bracket JL
• ALP-HRN-PSU300 PSU Power Harness
• ALP-THRN-CH2 Chrysler T-Harness
• CT6 6" Cable Ties
• PHPSM412 Pan Head Phillips Screw M4x12
• SLWM4 M4 Split Lock Washers
• PHSCR832 8-32 Pan Head Phillips screws
• PSS-WRA-IM Installation Manual

Features:

• Utilizes factory bolt locations
• Durable stamped, steel frame speaker basket design
• Includes template for mounting
• Vehicle specific T-harness for installation with OEM radio into compatible 2018 – Up Jeep® Wrangler and 2020 – Up Jeep® Gladiator vehicles
• Vehicle specific mounting brackets allow for the powered sub and amp to be secured under the passenger seat without drilling