Description
Included in this kit
This bundle includes a Rockford Fosgate M5-1500X5 5 Ch. Element Ready Amplifier 125x4 + 400x1 @ 4-Ohm, 200x4 + 700x1 @ 2-Ohm, Na + 700x1 @ 1-Ohm, 400x2 @ 4-Ohm + Na Bridged, and a Rockford Fosgate RFPOL-RC5 Polaris Ride Command Active Noise Reduction Adapter For Use With Stage 5 & 6 Kits.
1x Rockford Fosgate M5-1500X5 5 Ch. Element Ready Amplifier 125x4 + 400x1 @ 4-Ohm, 200x4 + 700x1 @ 2-Ohm, Na + 700x1 @ 1-Ohm, 400x2 @ 4-Ohm + Na Bridged (M5-1500X5)
Rockford Fosgate 1,500 Watt 5-Channel Element Ready™ Amplifier
The M5-1500X5 amplifier features the next level of Element Ready™ design from Rockford Fosgate that’s built as rugged as the outdoor environment it’s used in. The IPX6 rating is provided by splash guards on both ends and heavy-duty molded harnesses with integral sealing gaskets. A new PRESET switch - for use with Rockford Fosgate UTV audio kits - eliminates the need to set-up and tune the amp for the best experience possible. Built on the popular TM series, M5 amplifiers feature the same great technologies like Constant Power, Class-AD/BD and C.L.E.A.N., all engineered, developed, and validated in Tempe, Arizona.
Rockford Fosgate amplifiers are known world-wide for producing more power than their ratings suggest. The M5 amplifiers are the first series based on new industry standard Dynamic Power ratings, bringing their conservative ratings to the forefront. Engineered from the ground up and purpose-built to deliver more output where you actually hear it, this is real dynamic power that performs not only on paper, but performance heard through the musical experience. You’ll see two amplifier power ratings, the traditional Continuous Power output, and the new Dynamic Power output, both tested in accordance with the CTA-2006 specification. Consider Continuous Power as wattage developed on the test bench for comparison against other amplifiers in the same class, and Dynamic Power as real-world wattage when connected to a speaker load, listening to music. Either way you look at it, Rockford Fosgate is proving – once again – these amplifiers are powerful enough to drive any speaker or subwoofer you throw at them.
- Element Ready™ design with integrated harness & panel seals
- PRESET removes the need to set-up and tune the amp when used with Rockford Fosgate UTV audio kits
- Play all day, easy to integrate, and keep music playing for extended lengths of time
- C.L.E.A.N. input/output clip detection and indicator LEDs
- Constant Power provides instantaneous delivery of output over varying impedance loads
- Focused mass heat sink allows critical aluminum material to be located around hottest internal devices
- Top mounted control panel with Element Ready™ smoked lens cover
- OEM and aftermarket radio integration inputs
- Low Impedance Stability
- Proprietary testing using RATS (Rockford Automated Testing System)
- Proprietary Class-AD technology allows amplifier to produce more power with less current draw
- Class-BD technology provides 75-80% efficiency over traditional class A/B designs
- Discrete Surface Mount technology utilizes 1% tight-tolerances for high efficiency and reduced cross-talk
- MESHA 4 reduces MOSFET temps, lowers distortion, increases durability and prolongs device life span
- Chassis Isolation from mounting points greatly reduces possible introduction of vehicle noise
- Balanced Differential Inputs eliminates noise picked up by signal cables
- Remote-Out feature when using high level inputs
- 2-Year Warranty
General Specifications
CEA-2006 Compliant
Yes
Cta-2006 Compliant
Number of Channels
5
Total Power
(Sum of Rated Power)
(Sum of Rated Power)
1500 Watts
Rated Power
(RMS Continuous Power)
(RMS Continuous Power)
CTA-2006 Continuous Power Rating100W x 4 + 400W x 1 @ 4Ω
100W x 4 + 600W x 1 @ 2Ω
N/A + 600W x 1 @ 1Ω
200W x 2 + N/A @ 4Ω bridged
≤1.0% THD+N
Dynamic Power
(PVC/PowerCube®)
(PVC/PowerCube®)
CTA-2006 Dynamic Power Rating125W x 4 + 400W x 1 @ 4Ω
200W x 4 + 700W x 1 @ 2Ω
N/A + 700W x 1 @ 1Ω
400W x 2 + N/A @ 4Ω bridged
Bridgeable
Yes
Frequency Response
10Hz - 50kHz
Input Sensitivity
150mVrms - 12Vrms
Circuit Topology Class
Class-AD (front/rear channels)
Class-BD (sub channel)
Class-BD (sub channel)
Efficiency (average)
>75%
Total Harmonic Distortion (THD+Noise)
<0.2% THD+N @ 1 Watt
Signal Input
Low-Level: 2 RCA
High-Level: 4-Pin Molex
High-Level: 4-Pin Molex
Signal Output
—
Tone Controls
Front/Rear: 0-14dB @ 12.5kHz
Front/Rear: 0-18dB @ 45Hz
Sub: 0-18dB @ 45 Hz
Front/Rear: 0-18dB @ 45Hz
Sub: 0-18dB @ 45 Hz
Crossover Controls
High-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth
Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth
Infrasonic: 30 Hz @ 12dB/Octave Butterworth
50 Hz - 250 Hz @ 12dB/Octave Butterworth
Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth
Infrasonic: 30 Hz @ 12dB/Octave Butterworth
Remote Controls
No
Visual Indicators
Power: Blue
Protect: Red
Input Clip: Red
Output Clip: Blue/Red
Protect: Red
Input Clip: Red
Output Clip: Blue/Red
Power Wire Gauge
4 AWG
Power Input Connector
Compression Terminal Block
Speaker Wire Gauge
16 AWG
Speaker Output Connector
4-Pin Molex
Cooling
Convection
Heatsink
Extruded Aluminum
Operating Voltage
9 - 16 VDC
Recommended Fuse
(not included)
(not included)
—
Average Current Draw (13.8V Music)
—
Max. Current Draw (13.8V Sinewave)
90 A @ 4Ω/4Ω
140 A @ 2Ω/2Ω
170 A @ 2Ω/1Ω
150 A @ 4Ω bridged
140 A @ 2Ω/2Ω
170 A @ 2Ω/1Ω
150 A @ 4Ω bridged
Suggested Alternator
—
Dimensional Diagram
—
Dimensions (H x W x D)
1.7" x 4.25" x 12.3"
(42.8 mm x 108 mm x 311.4 mm)
Does not include harnesses
(42.8 mm x 108 mm x 311.4 mm)
Does not include harnesses
Shipping Weight
TBA
1x Rockford Fosgate RFPOL-RC5 Polaris Ride Command Active Noise Reduction Adapter For Use With Stage 5 & 6 Kits (RFPOL-RC5)
Audio interface designed for use with Polaris® vehicles equipped with Ride Command®. Allows Polaris® Ride Command® to function as your source unit. Uses Rockford Fosgate engineered circuitry to eliminate turn-on pop common with all Ride Command® units and noise in UTVs equipped with DYNAMIX suspension caused by switching between Firm, Sport, and Comfort modes. Compatible with all Polaris® RZR®, GENERAL™, and RANGER® models equipped with Ride Command®. The Ride Command® audio interface (RFPOL-RC5) is designed to connect Rockford Fosgate amplifiers with a factory Polaris® Ride Command® source unit. The two-part harness taps both front, rear and subwoofer audio signals from Ride Command®, actively filters any electronic noise caused by the DYNAMIX suspension system and feeds them to a TM1000X5ad amplifier. The front channels power the front audio, and the rear channels power the subwoofer. The kit also allows you to take advantage of built-in Ride Command® crossovers for the best sound possible. Since one harness interfaces with the front/rear speaker amp, and the second connects to the subwoofer amp, it ensures Ride Command® properly distributes the correct audio frequencies to the proper speakers.
Features:
Active electronic noise suppressor
Retains factory Ride Command® as audio source
Designed for RZR®, RANGER™, and GENERAL™ equipped with Ride Command®
Compatible with both 5-button and 7-button RIde Command®
Eliminates pulse width modulated Noise in DYNAMIX suspension system
Eliminates turn-on pop associated with Ride Command® unit
Feeds Front, Rear & Subwoofer audio from Ride Command® to amplifier
Utilizes built-in crossovers from Ride Command® (100 Hz HP & 100 Hz LP)
Includes remote-out to turn-on Rockford Fosgate amplifier
Harness plugs exclusively into TM1000X5ad
1 Year Warranty