Description
Included in this kit
This bundle includes a Wavtech LINK400.4MINI 400W RMS Compact 4-Channel Bridgeable Amplifier, and a Wavtech IRAD +12V Output/Remote Delay/Start-Stop Solenoid Control.
1x Wavtech LINK400.4MINI 400W RMS Compact 4-Channel Bridgeable Amplifier (LINK400.4MINI)
Wavtech LINK400.4MINI 400W RMS Compact 4-Channel Bridgeable Amplifier
A compact bridgeable amplifier with matrix summing, channel 3/4 bass tuning and factory-system integration.
Build a factory or aftermarket audio upgrade with the link400.4mini. This four-channel bridgeable amplifier combines matrix summing, adaptive OEM loading and speaker-level inputs up to 40Vrms. Channels 3/4 add a parametric EQ, subsonic filter and support for the optional linkRC remote level control. Start/stop compatibility and active thermal rollback support vehicle integration.
Power for flexible system layouts
The link400.4mini delivers 65 watts RMS per channel at 4 ohms or 100 watts RMS per channel at 2 ohms. Its 4/3/2-channel bridgeable design supports 200 watts RMS x 2 at 4 ohms in bridged operation, with ratings specified at 14.4V and less than 1% THD+N.
Combine and balance factory signals
The four-channel matrix summing processor allows direct, copied or summed channel-pair routing. Adaptive speaker-input loading supports OEM load-detect systems, while +/-6dB output level trim balances channel pairs after summing or copying. Differential balanced inputs accept speaker-level or RCA sources.
Channel 3/4 bass adjustment
The parametric EQ provides 0 to +12dB boost, adjustable Q from 1.4 to 5, and a 30–80Hz center frequency. A 10–50Hz subsonic filter operates at up to -24dB/octave. The optional linkRC adjusts channel 3/4 output from 0 to -30dB.
Two crossover ranges
Variable -12dB/octave high-pass and low-pass filters cover 50–500Hz in the x1 range or 500Hz–5kHz in the x10 range. Gain controls with clip LEDs help set source sensitivity without relying on guesswork.
Vehicle integration and installation
Automatic turn-on can detect DC offset or audio, with a wired remote trigger also supported. Start/stop compatibility and active thermal rollback are built in. The amplifier uses 4AWG power/ground terminals, 10AWG speaker outputs and detachable mounting tabs.
Technical specifications
| Model | link400.4mini |
| Configuration | 4/3/2-channel bridgeable |
| RMS power at 4 ohms | 65W x 4 |
| RMS power at 2 ohms | 100W x 4 |
| Bridged RMS power at 4 ohms | 200W x 2 |
| Power-rating conditions | 14.4V; less than 1% THD+N |
| Frequency response, extended | Below 10Hz to above 40kHz (+0/-3dB) |
| Frequency response, max flat | Below 10Hz to above 28kHz (+0/-1dB) |
| Speaker input sensitivity | 1–20Vrms / 2–40Vrms |
| RCA input sensitivity | 0.2–5Vrms / 0.4–10Vrms |
| HP/LP crossover | 50–500Hz or 500Hz–5kHz; -12dB/octave |
| Output level trim | +/-6dB |
| CH3/4 parametric EQ | 0 to +12dB boost; Q 1.4–5; 30–80Hz center frequency |
| CH3/4 subsonic filter | 10–50Hz; up to -24dB/octave |
| Optional remote level control | linkRC; channels 3/4; 0 to -30dB |
| External fuse / minimum power wire | 50A fuse; 8AWG wire; fuse not included |
| Power / ground terminals | 4AWG |
| Speaker output terminals | 10AWG |
| Operating range after startup | 7–16V; startup above 10.3V |
| Chassis dimensions (H x W x L) | 1.65 x 4.53 x 7.2 inches; excludes terminals/tabs |
| Overall dimensions (H x W x L) | 1.73 x 4.53 x 8.23 inches; includes terminals/tabs |
| Included items | Amplifier, speaker-level input terminals, pre-attached mounting tabs, hex wrenches, mounting screws |
Requires an external 50A fuse (not included) and minimum 8AWG power wiring. Install in a dry, ventilated location.
1x Wavtech IRAD +12V Output/Remote Delay/Start-Stop Solenoid Control (IRAD+)
The technology in the Patented IRAD make it the ultimate installation tool. It provides solutions to 3 very specific problems faced in today’s installations. This easy to program device allows you to add a switched 12-volt output, a remote output with adjustable delay and a relay/solenoid control to overcome the issues created by vehicles with start/stop systems.
IRAD Features
Automatic 12V Ignition Detection and +12V Output Generation
Generated +12V Remote Output (direct or linked to IGN)
Stop-Start Relay/Solenoid Control Mode
Independent Adjustable IGN & REM Turn-On/Off Delays
>750mA Continuous Current Per Output
Compact Aluminum Chassis w/Detachable Mounting Tabs
Locking Detachable Terminals
Chassis Dimensions: 0.79”x1.5”x1.5” (20x38x37mm)